/* hp.c: A HP LAN ethernet driver for linux. */ /* Written 1993 by Donald Becker. Copyright 1993 United States Government as represented by the Director, National Security Agency. This software may be used and distributed according to the terms of the GNU Public License, incorporated herein by reference. This is a driver for the HP LAN adaptors. The Author may be reached as becker@super.org or C/O Supercomputing Research Ctr., 17100 Science Dr., Bowie MD 20715 */ static char *version = "hp.c:v0.99.13f 10/16/93 Donald Becker (becker@super.org)\n"; #include #include #include #include #include #include #include #ifndef port_read #include "iow.h" #endif #include "dev.h" #include "8390.h" #define HP_DATAPORT 0x0c /* "Remote DMA" data port. */ #define HP_ID 0x07 #define HP_CONFIGURE 0x08 /* Configuration register. */ #define HP_RUN 0x01 /* 1 == Run, 0 == reset. */ #define HP_IRQ 0x0E /* Mask for software-configured IRQ line. */ #define HP_DATAON 0x10 /* Turn on dataport */ #define NIC_OFFSET 0x10 /* Offset the 8390 registers. */ #define HP_START_PG 0x00 /* First page of TX buffer */ #define HP_8BSTOP_PG 0x80 /* Last page +1 of RX ring */ #define HP_16BSTOP_PG 0xFF /* Last page +1 of RX ring */ int hp_probe(struct device *dev); int hpprobe1(int ioaddr, struct device *dev); static void hp_reset_8390(struct device *dev); static int hp_block_input(struct device *dev, int count, char *buf, int ring_offset); static void hp_block_output(struct device *dev, int count, const unsigned char *buf, const start_page); static void hp_init_card(struct device *dev); /* The map from IRQ number to HP_CONFIGURE register setting. */ /* My default is IRQ5 0 1 2 3 4 5 6 7 8 9 10 11 */ static char irqmap[16] = { 0, 0, 4, 6, 8,10, 0,14, 0, 4, 2,12,0,0,0,0}; /* Probe for an HP LAN adaptor. Also initialize the card and fill in STATION_ADDR with the station address. */ int hp_probe(struct device *dev) { int *port, ports[] = {0x300, 0x320, 0x340, 0x280, 0x2C0, 0x200, 0x240, 0}; short ioaddr = dev->base_addr; if (ioaddr > 0x1ff) /* Check a single specified location. */ return ! hpprobe1(ioaddr, dev); else if (ioaddr > 0) /* Don't probe at all. */ return ENXIO; for (port = &ports[0]; *port; port++) { #ifdef HAVE_PORTRESERVE if (check_region(*port, 32)) continue; #endif if (inb_p(*port) != 0xff && hpprobe1(*port, dev)) { return 0; } } dev->base_addr = ioaddr; return ENODEV; } int hpprobe1(int ioaddr, struct device *dev) { int i; unsigned char *station_addr = dev->dev_addr; int tmp; /* Check for the HP physical address, 08 00 09 xx xx xx. */ if (inb(ioaddr) != 0x08 || inb(ioaddr+1) != 0x00 || inb(ioaddr+2) != 0x09) return 0; /* This really isn't good enough, we may pick up HP LANCE boards also! */ ethdev_init(dev); ei_status.tx_start_page = HP_START_PG; ei_status.rx_start_page = HP_START_PG + TX_PAGES; /* Set up the rest of the parameters. */ if ((tmp = inb(ioaddr + HP_ID)) & 0x80) { ei_status.name = "HP27247"; ei_status.word16 = 1; ei_status.stop_page = HP_16BSTOP_PG; /* Safe (if small) value */ } else { ei_status.name = "HP27250"; ei_status.word16 = 0; ei_status.stop_page = HP_8BSTOP_PG; } printk("%s: %s at %#3x,", dev->name, ei_status.name, ioaddr); for(i = 0; i < ETHER_ADDR_LEN; i++) printk(" %2.2x", station_addr[i] = inb(ioaddr + i)); /* Set the base address to point to the NIC, not the "real" base! */ dev->base_addr = ioaddr + NIC_OFFSET; /* Snarf the interrupt now. Someday this could be moved to open(). */ if (dev->irq < 2) { int irq_16list[] = { 11, 10, 5, 3, 4, 7, 9, 0}; int irq_8list[] = { 7, 5, 3, 4, 9, 0}; int *irqp = ei_status.word16 ? irq_16list : irq_8list; do { if (request_irq (dev->irq = *irqp, NULL) != -EBUSY) { autoirq_setup(0); /* Twinkle the interrupt, and check if it's seen. */ outb_p(irqmap[dev->irq] | HP_RUN, ioaddr + HP_CONFIGURE); outb_p( 0x00 | HP_RUN, ioaddr + HP_CONFIGURE); if (dev->irq == autoirq_report(0) /* It's a good IRQ line! */ && request_irq (dev->irq, &ei_interrupt) == 0) { printk(" selecting IRQ %d.\n", dev->irq); break; } } } while (*++irqp); if (*irqp == 0) { printk(" no free IRQ lines.\n"); return 0; } } else { if (dev->irq == 2) dev->irq = 9; if (irqaction(dev->irq, &ei_sigaction)) { printk (" unable to get IRQ %d.\n", dev->irq); return 0; } } #ifdef HAVE_PORTRESERVE snarf_region(ioaddr, 32); #endif if (ei_debug > 1) printk(version); ei_status.reset_8390 = &hp_reset_8390; ei_status.block_input = &hp_block_input; ei_status.block_output = &hp_block_output; hp_init_card(dev); return dev->base_addr; } static void hp_reset_8390(struct device *dev) { int hp_base = dev->base_addr - NIC_OFFSET; int saved_config = inb_p(hp_base + HP_CONFIGURE); int reset_start_time = jiffies; if (ei_debug > 1) printk("resetting the 8390 time=%d...", jiffies); outb_p(0x00, hp_base + HP_CONFIGURE); ei_status.txing = 0; sti(); /* We shouldn't use the boguscount for timing, but this hasn't been checked yet, and you could hang your machine if jiffies break... */ { int boguscount = 150000; while(jiffies - reset_start_time < 2) if (boguscount-- < 0) { printk("jiffy failure (t=%d)...", jiffies); break; } } outb_p(saved_config, hp_base + HP_CONFIGURE); while ((inb_p(hp_base+NIC_OFFSET+EN0_ISR) & ENISR_RESET) == 0) if (jiffies - reset_start_time > 2) { printk("%s: hp_reset_8390() did not complete.\n", dev->name); return; } if (ei_debug > 1) printk("8390 reset done (%d).", jiffies); } /* Block input and output, similar to the Crynwr packet driver. If you porting to a new ethercard look at the packet driver source for hints. The HP LAN doesn't use shared memory -- we put the packet out through the "remote DMA" dataport. */ static int hp_block_input(struct device *dev, int count, char *buf, int ring_offset) { int nic_base = dev->base_addr; int saved_config = inb_p(nic_base - NIC_OFFSET + HP_CONFIGURE); int xfer_count = count; outb_p(saved_config | HP_DATAON, nic_base - NIC_OFFSET + HP_CONFIGURE); outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, nic_base); outb_p(count & 0xff, nic_base + EN0_RCNTLO); outb_p(count >> 8, nic_base + EN0_RCNTHI); outb_p(ring_offset & 0xff, nic_base + EN0_RSARLO); outb_p(ring_offset >> 8, nic_base + EN0_RSARHI); outb_p(E8390_RREAD+E8390_START, nic_base); if (ei_status.word16) { port_read(nic_base - NIC_OFFSET + HP_DATAPORT,buf,count>>1); if (count & 0x01) buf[count-1] = inb(nic_base - NIC_OFFSET + HP_DATAPORT), xfer_count++; } else { port_read_b(nic_base - NIC_OFFSET + HP_DATAPORT, buf, count); } /* This is for the ALPHA version only, remove for later releases. */ if (ei_debug > 0) { /* DMA termination address check... */ int high = inb_p(nic_base + EN0_RSARHI); int low = inb_p(nic_base + EN0_RSARLO); int addr = (high << 8) + low; /* Check only the lower 8 bits so we can ignore ring wrap. */ if (((ring_offset + xfer_count) & 0xff) != (addr & 0xff)) printk("%s: RX transfer address mismatch, %#4.4x vs. %#4.4x (actual).\n", dev->name, ring_offset + xfer_count, addr); } outb_p(saved_config & (~HP_DATAON), nic_base - NIC_OFFSET + HP_CONFIGURE); return ring_offset + count; } static void hp_block_output(struct device *dev, int count, const unsigned char *buf, const start_page) { int nic_base = dev->base_addr; int saved_config = inb_p(nic_base - NIC_OFFSET + HP_CONFIGURE); outb_p(saved_config | HP_DATAON, nic_base - NIC_OFFSET + HP_CONFIGURE); /* Round the count up for word writes. Do we need to do this? What effect will an odd byte count have on the 8390? I should check someday. */ if (ei_status.word16 && (count & 0x01)) count++; /* We should already be in page 0, but to be safe... */ outb_p(E8390_PAGE0+E8390_START+E8390_NODMA, nic_base); #ifdef ei8390_bug /* Handle the read-before-write bug the same way as the Crynwr packet driver -- the NatSemi method doesn't work. */ outb_p(0x42, nic_base + EN0_RCNTLO); outb_p(0, nic_base + EN0_RCNTHI); outb_p(0xff, nic_base + EN0_RSARLO); outb_p(0x00, nic_base + EN0_RSARHI); outb_p(E8390_RREAD+E8390_START, EN_CMD); /* Make certain that the dummy read has occured. */ inb_p(0x61); inb_p(0x61); #endif outb_p(count & 0xff, nic_base + EN0_RCNTLO); outb_p(count >> 8, nic_base + EN0_RCNTHI); outb_p(0x00, nic_base + EN0_RSARLO); outb_p(start_page, nic_base + EN0_RSARHI); outb_p(E8390_RWRITE+E8390_START, nic_base); if (ei_status.word16) { /* Use the 'rep' sequence for 16 bit boards. */ port_write(nic_base - NIC_OFFSET + HP_DATAPORT, buf, count>>1); } else { port_write_b(nic_base - NIC_OFFSET + HP_DATAPORT, buf, count); } /* DON'T check for 'inb_p(EN0_ISR) & ENISR_RDC' here -- it's broken! */ /* This is for the ALPHA version only, remove for later releases. */ if (ei_debug > 0) { /* DMA termination address check... */ int high = inb_p(nic_base + EN0_RSARHI); int low = inb_p(nic_base + EN0_RSARLO); int addr = (high << 8) + low; if ((start_page << 8) + count != addr) printk("%s: TX Transfer address mismatch, %#4.4x vs. %#4.4x.\n", dev->name, (start_page << 8) + count, addr); } outb_p(saved_config & (~HP_DATAON), nic_base - NIC_OFFSET + HP_CONFIGURE); return; } /* This function resets the ethercard if something screws up. */ static void hp_init_card(struct device *dev) { int irq = dev->irq; NS8390_init(dev, 0); outb_p(irqmap[irq&0x0f] | HP_RUN, dev->base_addr - NIC_OFFSET + HP_CONFIGURE); return; } /* * Local variables: * compile-command: "gcc -D__KERNEL__ -Wall -O6 -I/usr/src/linux/net/inet -c hp.c" * version-control: t * kept-new-versions: 5 * End: */